Our Online Store Is Now Available For Ordering.

Protecting the Drive Train: Bearings, Gearbox Oil and Shock Absorbers

Table of Contents

Small, cheap tasks on a steady schedule prevent the most expensive failures.

Key Takeaways

  • Grease bearings monthly with high-temperature NLGI 3 grease or heavier.
  • Track bearing temperatures; call service if one climbs toward 160 degrees F.
  • Change gearbox oil on an operating-hours schedule.
  • Replace cracked drive shock absorbers before they cost a gearbox.

The drive train turns motor speed into the torque that cuts plastic, and it absorbs a shock every time a knife meets a hard piece of purge. Bearings, gearbox oil and drive shock absorbers are inexpensive to maintain and very expensive to replace after a failure. Here is a preventive plan built around all three.

The Drive Train at a Glance

Bearings: Grease and Temperature

Use a high-temperature NLGI 3 grease or heavier and grease at least monthly. Low-temperature grease thins out in a warm bearing and runs out of the housing. On lines processing glass-filled or other abrasive material, never stretch the interval: fresh grease also flushes abrasive dust out.

Bearing temperature after several hours of running


Track readings monthly with an infrared thermometer. A bearing much hotter than its neighbors needs attention; call service at 239-235-9930.

Gearbox Oil

Gearbox oil breaks down and collects fine metal wear particles. Draining and refilling every 2,000 operating hours with ISO VG 220 or higher keeps the gear set healthy and flushes those particles out.

Drive Shock Absorbers

On all shredders, rubber elements between the motor and gearbox take the impact load. Inspect them every three months and replace them about every two years, or immediately if the rubber is cracking or crumbling. They cost a small fraction of a gearbox, and replacements are available through our webstore, Virtus Equipment Direct, or our parts specialist at 239-219-1500.

Preventive Maintenance Calendar

Task Interval Why
Grease bearings Monthly Lubricate and flush contamination
Read bearing temperatures Monthly Catch failing bearings early
Inspect shredder shock absorbers Every 3 months Protect the gearbox
Change gearbox oil (ISO VG 220+) Every 2,000 hours Remove wear particles
Change hydraulic oil (ISO VG 46) and filter Every 2,000 hours Protect the pusher cylinder
Replace shredder shock absorbers Every 2 years Before rubber fails

The Cost Case

A tube of grease, a few liters of oil and a set of rubber elements cost little. A seized bearing or a cracked gearbox means a long stop, a large invoice and lost production. Put these tasks on the same calendar as your knife and screen checks.

ZERMA America Videos: Heavy Duty ShreddersSearch the ZERMA America YouTube channelZERMA America on YouTubeBrowse all ZERMA America videos

Frequently Asked Questions

What grease suits shredder and granulator bearings?
A high-temperature NLGI 3 grease or heavier, applied at least monthly.

Why is a shredder bearing running hotter than normal?
Missed greasing, grease that cannot handle heat, or a bearing starting to wear. Contact service if a bearing keeps climbing or runs much hotter than the others.

Does gearbox oil need regular changes?
Yes. It breaks down and collects metal wear particles. Change it every 2,000 operating hours using ISO VG 220 or higher.

Should drive shock absorbers be part of routine inspections?
Yes. Inspect them regularly and replace them when the rubber cracks, before the gearbox takes the damage.

Need Parts, Service or a Second Opinion?

Our team in Fort Myers, Florida keeps wear and replacement parts in stock and can help you troubleshoot, size a machine or plan maintenance. Replacement parts can be purchased any time through our webstore, Virtus Equipment Direct.

Sales: 239-219-1100 · Parts: 239-219-1500 · Service: 239-235-9930 (bilingual in Spanish) · sales@zerma-america.com

Related Resources

© 2026 ZERMA America. All Rights Reserved. Content, images, graphics, and advertisementsmay not be reproduced, distributed, or reused without prior written permission. When permission is granted, proper credit is required. Brief quotations with attribution and a link to the original post are permitted. Contact Recycling Specialist for permission requests.

error: Content is protected !!